Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Performance

Reply
 
Thread Tools Search this Thread Display Modes
  #41  
Old 09-07-2021, 05:04 PM
FLexpat FLexpat is offline
Senior Member
 
Join Date: Dec 2013
Location: Park City UT & around FL
Posts: 655
Default

Volvo Penta used the crank mounted pumps on the SBCs for years. Marine Power as well. I have had them and was pretty happy even though it took me a bit to trust it. The way they use a rubber bushing around the arm bolt takes up a lot of flex/vibration. You can change the impeller pretty easily and if you have it set up with shutoff valves, you can do that in the water. My only concern would be getting enough cooling since it looks like you will end up with a pretty high performance motor.
Reply With Quote
  #42  
Old 09-08-2021, 01:01 AM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

Brother you just hit my greatest concern. I have no idea if this will be adequate cooling.

I bought a 350,000 BTU heat exchanger and you can see my diagram below. I figure I’ll spend a small fortune in fittings and hoses but throughput is gonna be the name of the game. Assuming this cools adequately keeping it flowing is next priority.

It does have a shut off valve on 1.25” water inlet to strainer, to pump, to various fittings. I’m running the biggest hoses I can think of and utilizing both sides of elbows in/out to promote quick circulation.

I have a friend that runs the biggest cooling, refrigeration hvac (grocery stores etc freezers and a/c) for the island/state. He did some math and recommended this setup. But between us, I have no clue of this will work. Only one way to find out I suppose.

Last edited by Xcomunic8d; 09-08-2021 at 01:04 AM.
Reply With Quote
  #43  
Old 09-11-2021, 08:53 AM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,136
Default

Do you have more specs than just 350,000 BTU/h? At what temperatures, flows, etc?


I have done these sorts of calculations for piston aircraft engines- I *might* be able to help.





Quote:
Originally Posted by Xcomunic8d View Post
Brother you just hit my greatest concern. I have no idea if this will be adequate cooling.

I bought a 350,000 BTU heat exchanger and you can see my diagram below. I figure Iíll spend a small fortune in fittings and hoses but throughput is gonna be the name of the game. Assuming this cools adequately keeping it flowing is next priority.

It does have a shut off valve on 1.25Ē water inlet to strainer, to pump, to various fittings. Iím running the biggest hoses I can think of and utilizing both sides of elbows in/out to promote quick circulation.

I have a friend that runs the biggest cooling, refrigeration hvac (grocery stores etc freezers and a/c) for the island/state. He did some math and recommended this setup. But between us, I have no clue of this will work. Only one way to find out I suppose.
Reply With Quote
  #44  
Old 09-11-2021, 02:34 PM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

40 GPM 4-1” ports on exchanger. Rated at 350,000 BTU. Using 1.25” hoses to feed water into and out of exchanger. See post 30 for thorough diagrams of system.

About all I know on it. 5.3 engine. 400-450hp output is my guess expect to spend most of my time 1500 rpm for trolling.

Any help greatly appreciated. I’m trusting other people on this one.

Last edited by Xcomunic8d; 09-11-2021 at 08:34 PM.
Reply With Quote
  #45  
Old 09-13-2021, 08:15 PM
FishStretcher FishStretcher is offline
Senior Member
 
Join Date: Dec 2010
Location: Greater Boston
Posts: 1,136
Talking

I can only offer you a modest amount of guidance based on experience with other engines.



I did a fair amount of cooling work on Rotax 912 IS sport 100hp 4 cylinder aircraft engines. These were liquid cooled heads, but air cooled cylinders. And an oil cooler.



Crucially, they can operate for a long time at or near full power, like a marine engine.


For a 100HP engine (metric HP, but close enough for what we are discussing here) they were rated at 73.5kW for 5 minutes or 72kW continuous


Go to flyrotax.com and look for the installation manual for details: d06847.pdf


They required 30kW of liquid cooling, 6kW of air cooling and 10kW of oil cooling for takeoff. Takeoff is the worst condition, especially for oil cooling because of this highest engine speed.


In my experience, this air cooling was largely unneccesary except at above 80% power.

So, if we think the GM 5.3 is more efficient than a Rotax 912 iS Sport, and it probably is, then an estimate would be 30kW of water cooling 6kW of air cooling and 10kW of oil cooling for every 100HP at the crank.


So for the estimate: for every 100 metric HP you make 73.5kW shaft power and need 46kW of cooling.

Again, the 5.3 may make less heat, it's a modern engine.



You say you cam make 400HP. That's at WOT, at maximum engine speed. Power requirements are very approximately related to the cube of speed. So at 80% speed, you will need very approximately 51.2% power. (and heat rejection). Or 200HP.


So at 80% speed at 200HP, you need 2x(30+6+10)kW cooling. Call that 92kW heat rejection.


You have 350,000BTU/h heat rejection. My online calculator and a couple of references make me think this is 102.5kW.



So. For a first guess- I think you might overheat running at full throttle at full engine speed. But you are probably fine for almost all operation.


This is just a guess- a slightly scientific guess with a reference, but just a guess. You could be OK at all speeds. I don't think this is a terrible place to start for cooling. But it doesn't seem overcooled.


Remember, this is just an opinion that you got on the internet, using a different engine as a benchmark.
Reply With Quote
  #46  
Old 09-13-2021, 08:47 PM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

It has occurred to me that I made an error in telling you it will only be 350k btu’s. That’s the main heat exchanger however there will be additional 50k (25k for power steering and oil each). So I’ll try to figure out what that looks like.

Heat soak is also a concern. I plan to have a bilge vent blower on the bilge exhaust side keyed to ignition so it pulls hot air out of the compartment and should draw cooler air in naturally. This blower is not to be confused with another blower I will install for venting gas fumes.

Thanks for doing all this math. There really is only one way to find out for sure. It will have a ps cooler and an oil cooler.

If needed a bigger exchanger is not the end of the world. But we will see. I’ll get up on plane and get going fast on rare occasions but majority is high speed trolling. 13mph. Give or take conditions.

Last edited by Xcomunic8d; 09-14-2021 at 01:19 AM.
Reply With Quote
  #47  
Old 09-30-2021, 02:54 PM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

So itís been a lot of hurry up and wait here. Not sure I posted this but all 3 of my kids tested positive for COVID. And per Hawaii law, all of us (me, wife, and kids) were quarantined for over 20 days.

Wiring-

I did end up getting a LS1 stand-alone harness. I couldnít find a gen 4 stand-alone. Turns out the 2008 was an oddball Ls due to connectors etc.

https://www.ebay.com/itm/313583141284

I did have to cut off and replace the ev1 to ev6 injector connectors. From old harness. This was free for me. Iíve read mixed reviews on adapters and this way itís permanent.

The map sensor I had looks compatible but if you do this double check that
I did have to order some older style O2 sensors denso 234-4337
The coil brackets, coil harnesses, and coil harness extenders have finally come in this week. Took about 3 weeks to get those. And the flexible oil dipstick says oct-nov to arrive.

My harness came with compatible parts idís. I ordered a maf sensor. Will probably need an ait sensor as well.

My pcm came in from lt1swap.com Brendon was great and super fast to work with. very close to being ready to start this.

Must have a ligenfelter trg-002. The Holley terminator xís are still not in stock.
Need a 4pin to 2 pin alternator connector. Iíve thought about wiring it up myself but still reviewing harness diagrams. I do have a resistor here and maybe I can make that setup work. Weíll see. The ict billet 4pin to 2 pin waalt30-6 is only $30.

Will be ordering gauges soon. Think Iíll be going with Faria Chesapeake in black.

https://www.boatid.com/faria-beede-i...iABEgJ8SPD_BwE

And need fuel system. Mainly a pump. Anyone have suggestions for inline fuel pumps? Iím thinking about an inline pump from summit and keeping an evil energy from Amazon onboard as a backup.

Itíd be pretty pricey to put in tank pumps in and really a pain if they failed.
Reply With Quote
  #48  
Old 09-30-2021, 07:56 PM
wattaway2 wattaway2 is offline
Senior Member
 
Join Date: Oct 2011
Location: Ft.Lauderdale,Fl.
Posts: 570
Default

Glad to here your out of quarantine and since you didnít add anything I assume everyone is doing well!? God help anyone else that might try and work on it down the road😀but sure sounds like youíve got it figured out! Hope the Lava isnít a issue . My step daughter in Capt. Cook is ok
Reply With Quote
  #49  
Old 09-30-2021, 08:44 PM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

Iím never parting with this boat. I hope Iím happy with performance. Family is all aok. The lava is all in the volcano park a good bit away. A few years back it was flowing and within 10 miles of me.

I live in HPP. You step daughter should know where that is diagonally NE from her to me roughly. Rainy season is starting here I got to get a cover up ASAP.
Reply With Quote
  #50  
Old 10-05-2021, 04:27 AM
Xcomunic8d Xcomunic8d is offline
Senior Member
 
Join Date: Oct 2016
Location: Hilo, HI
Posts: 198
Default

I put another order in with summit

This ones for the fuel pump, ligenfelter converter trg-002, 4 pin to 2 pin alt harness, and msd custom plug wire kit.

Thatís gonna get me really close to firing it up. I need to order some gauges, fuel hoses, regulator, and some other stuff but nothing too major left on the engine.

I canít wait to fire it up, or at least try to. Iím sure Iíll have some issues to work out.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
All original content © 2003-2018 ClassicSeacraft